PUFFY FOAM - CLASSIC 3MM
Give your embroidery design dimension! Gunold’s Puffy Foam is a high-quality 3D embroidery foam that is waterresistant,
non-toxic, and can be machine washed and dry cleaned. The classic 3 mm has a nice give to it to create
curved edges.
WATCH PRODUCT
Puffy Foam
VIDEO ONLINE!
GU-620 WHT
ITEM NO. COLOR SIZE EACH
STANDARD 3 MM PUFFY FOAM SHEETS
GU-620 BLK BLACK 12" x 18" cut sheet Standard 3MM $1.89
GU-620 WHT WHITE 12" x 18" cut sheet Standard 3MM $1.89
GU-620 TAN TAN 12" x 18" cut sheet Standard 3MM $1.89
GU-620 RED RED 12" x 18" cut sheet Standard 3MM $1.89
GU-620 GRY GRAY 12" x 18" cut sheet Standard 3MM $1.89
GU-620 BLU DARK BLUE 12" x 18" cut sheet Standard 3MM $1.89
GU-620 ROY ROYAL 12" x 18" cut sheet Standard 3MM $1.89
GU-620 LIM LIME 12" x 18" cut sheet Standard 3MM $1.89
Create 3D Effects with Puffy Foam!
GU-620 BRN BROWN 12" x 18" cut sheet Standard 3MM $1.89
GU-620 YLW YELLOW 12" x 18" cut sheet Standard 3MM $1.89
Hi Dense Puffy Foam
GU-620 PNK PINK 12" x 18" cut sheet Standard 3MM $1.89
HI DENSE PUFFY FOAM
Gunold’s newest 3D Hi Dense Puffy Foam is a smash! Hi Dense is 44% more dense than the classic foam, but still
3 mm thick, which allows you to create sharp, square edges on your 3D designs. Like the classic Puffy Foam, it is
water-resistant, non-toxic, and can be machine washed and dry cleaned.
ITEM NO. COLOR SIZE EACH
3MM HI DENSE PUFFY FOAM SHEETS
GU-621 BLK BLACK 12" x 18" cut sheet Hi Dense $4.49
GU-621 WHT WHITE 12" x 18" cut sheet Hi Dense $4.49
GU-621 RED RED 12" x 18" cut sheet Hi Dense $4.49
GU-621 ROY ROYAL 12" x 18" cut sheet Hi Dense $4.49
Classic Puffy Foam Assorted Pack
Classic 3 mm Puffy Foam assortment pack. One 9"x6" sheet of Black, Brown, Coral,
Hi Dense Puffy Foam GU-621
Dark Blue, Forest, Gray, Kelly, Pink, Purple, Red, Royal, Tan, White, and Yellow.
WATCH PRODUCT
VIDEO ONLINE!
ITEM NO. PRODUCT EACH
GU-628 Puffy Foam Assorted Pack - 14 Colors $11.50
TIP: USING PUFFY FOAM
Give your design new life by adding dimension with Puffy Foam. It is best to match your thread color to the foam color in case any of the foam
D happens to peek through the design. Select a design that has enclosed areas like circles, letters, or shapes that taper to a point. Be sure your
a v e's Ti p
design has satin stitch areas wide enough to accommodate the foam.
If you have the ability in your embroidery software to control your stitch density, increase the density of the underlay stitches so that they are closer together,
and then place a heavy layer of satin stitches on top. The density on the top layer should be almost double the normal density. If you don’t have the ability to
adjust your density values, you will simply stitch the satin areas twice. In either case, follow this procedure:
• Stitch any fill stitch areas that precede the satin areas that you want to puff. Before the satin areas are stitched, lay down a piece of foam in the area to be
stitched. You may wish to use a very small amount of embroidery spray adhesive to attach it to the location.
• Stitch the underlay, or the first layer of satin stitches. After it is complete, gently pull away the foam. Stitch again over the area with the final layer, which
will encase the foam inside.
• To remove any remaining hairy bits, place a pressing cloth over the area and press lightly with a hand iron. The small foam bits will shrink up and disappear.
108 TOLL FOAM Y PUFF •EMBROIDERY
FREE 800-968-7550 Prices listed in this catalog are subject to change with out notice. WWW.ONESTOPINC.COM
/WWW.ONESTOPINC.COM